Are Arista 100G Transceivers Interoperable with Other 100G Transceivers Available in the Industry

Are Arista 100G Transceivers Interoperable with Other 100G Transceivers Available in the Industry?

It depends on the type of 100G transceivers you are referring to. Arista supports a full range of 100G copper cables and optical transceivers compliant to IEEE standards and industry MSAs. 聽Arista’s 100G transceivers are compatible with QSFP28 form factor and can interoperate with existing third-party switches and routers in the network. However, some 100G transceivers use different optical modulation schemes that may not be compatible with each other. For example, the 100G-DR / FR / LR modules will not interoperate with legacy 100G modules (such as CWDM4, LR4, etc), but they will interop with 400G-DR4 and 400G-XDR4.聽As long as the non-Arista 100G transceivers meet the associated industry standard specifications, Arista 100G transceivers are fully interoperable.

FAQS

Q: 400G QSFP-DD vs 400G OSFP/CFP8: What are the differences?

A: The table below includes detailed comparisons for the three main form factors of 400G transceivers.

Q: How does the QSFP+ to SFP+ fiber convertor allow 4x 10G?

A: To enable 4x 10G connectivity, a QSFP+ to SFP+ fiber converter utilizes a breakout cable. This cable splits the 40G channel provided by the QSFP+ transceiver into four individual 10G channels, each connected to an SFP+ transceiver. Essentially, the converter breaks down the high-speed 40G signal into four separate 10G signals, allowing each SFP+ port to transmit data at 10G speeds. This configuration is beneficial for scenarios where equipment with SFP+ interfaces needs to communicate with a device equipped with a QSFP+ port, providing flexibility and compatibility in networking setups.

Q: What does “SR8”, “DR4”, “XDR4”, “FR4”, and “LR4” mean?

A: “SR” refers to short range, and “8” implies there are 8 optical channels. “DR” refers to 500m reach using single-mode fiber, and “4” implies there are 4 optical channels. “XDR4” is short for “eXtended reach DR4”. And “LR” refers to 10km reach using single-mode fiber.

Q: Can I plug an OSFP transceiver module into a QSFP-DD port?

A: No. QSFP-DD and OSFP are totally different form factors. For more information about QSFP-DD transceivers, you can refer to 400G QSFP-DD Transceiver Types Overview. You can use only one kind of form factor in the corresponding system. E.g., if you have an OSFP system, OSFP transceivers and cables must be used.

Q: What other breakout options are possible apart from using OSFP modules mentioned above?

A: OSFP 400G DACs & AOCs are possible for breakout 400G connections. See 400G Direct Attach Cables (DAC & AOC) Overview for more information about 400G DACs & AOCs.

Q1: What is the difference between QSFP28 ER4 and QSFP28 ER4 Lite Module?

A: The QSFP 100G ER4 has a series of BER requirements of better than 1E-12 without FEC optical modules. However, the receiving sensitivity of 100G QSFP28 ER4 is not satisfied with the existing APD technology. Therefore, many optical module manufacturers/suppliers defined a non-standard 100Gbase ER4 Lite module with a QSFP28 package where the largest transmission distance is up to 40km with FEC or 30km without FEC.?Walsun provides the QSFP28 100G ER4 Lite module compliant with the Ethernet 100Gbase ER4 Lite standard to meet the harshest external operating conditions including temperature, humidity, and EMI interference.

Q2: How does the QSFP 100G ER4 Module differ from the QSFP28 4WDM?

A: The QSFP 100G ER4 optical transceiver supports dual 100G Ethernet applications while the 100G QSFP28 4DWM only supports 100G Ethernet applications. The commons and differences are listed below.